Viện Cơ khí động lực – Đại học Bách Khoa Hà Nội

Projects	Time
Design a ABS system for pneumatic brake system used on automobile assembled in Vietnam. KC03.05/11-15.	2012 – 2014
Project on completing design, assembly car with 6-8seats, assembled in Vietnam. CK.05.
Applied research appropriate technology for manufacturing hydraulic typical elements of tanks control system.

Projects	Time
Design forklifts, cranes, and transport machineforthe urbanVietnamused onlargecities.
Research drivetrain system ofautomobileused, producedin Vietnam.

Projects	Time
B2010-01-352: Design, make a prototype of braking control system to improve stability of vehicle.	2011
B2009-01-143 : Optimization Aerodynamic of passenger car body produced in Vietnam.	2010
Development software to calculate passenger car frames assembled in the factories of the Automotive Industry Corporation Vietnam.
Analyze the competitiveness of the category automobile manufactured, assembled in Vietnam.
Research-oriented developmentofthe automotive industryto 2010, withavisionto2020.
Design small truck models with capacity from 0.5-1.25 tones for service in transport rural and mountainous areas of Vietnam.

Projects	Time
T2012 – 89: Application Research excess energy in the electricity sector for public transport	2012
T2012 – 92: Design a controller(ECU) for the electric power steering system-EPS	2012
T2012 – 89 : Solutions to improve the safety of semi-trailers in the Vietnam transportation system	2012
T2012 – 88: Design a Electronic throttle system for motorbike to improve fuel economy	2012
T2011-85: Analyzing durability of automotive air conditioning compressor test bench by 3D simulation for laboratory	2011
T2011 – 75: Design diagnostic device for electronic control brake system on automobile	2011
T2010 – 114: Software for teaching Automotive structure–mechanical gear-box of front drive axle cars	2010
T2010 – 121: Research on control the slide of vehicle wheel when braking using Pulse width modulation – PWM	2010

You must be logged in to post a comment.

Vu, T. V., Pham, B. D., Pham, P. H., Vu, H. V., & Tran, B. X. , “ A numerical study of hollow water drop breakup during freezing", Physics of Fluids, 33(11), 112110, SCIE, Q1, IF: 3.521, https://doi.org/10.1063/5.0071795

Tran, X. B, “ Nonlinear Control of a Pneumatic Actuator Based on a Dynamic Friction Model ", Strojniski Vestnik/Journal of Mechanical Engineering, 67(9), SCIE, Q3, IF: 1.554, https://doi.org/10.5545/sv-jme.2021.7236.

Khong Vu Quang, Nguyen Duy Tien, Vu Minh Dien, Le Manh Toi, Le Dang Duy, “ Developing a waste heat recovery tube used in the seawater distillation system", Applied Thermal Engineering, Vol. 195 (2021), SCI, Q1, IF: 5,295, DOI: https://doi.org/10.1016/j.applthermaleng.2021.117229

Cong-Truong Dinh , The-Mich Nguyen, Tai-Duy Vu, Sung-Goon Park and Quang-Hai Nguyen, “ Numerical investigation of truncated-root rib on heat transfer performance of internal cooling turbine blades ", Physics of Fluids, Online 07 July 2021, Vol. 33, 076104, ISSN: 1070-6631, SCI, Q1, IF:3.521, DOI: https://doi.org/10.1063/5.0054149 .

Xuan-Truong Le , Duc-Anh Nguyen, Cong-Truong Dinh and Quang-Hai Nguyen “ Effect of Two-Head Flared Hole on Film Cooling Performance over a Flat Plate ", Aerospace, Online 4 May 2021, Vol. 8(5), 128, ISSN: 2226-4310, SCIE, Q3, IF:1.63, DOI: https://doi.org/10.3390/aerospace8050128.

Doan Nguyen Cong, Khanh Nguyen Duc , Vinh Nguyen “ The effects of dimethyl ether enriched air (DMEA) on exhaust pollutants and performance characteristics of an old generation diesel engine ", International Journal of Sustainable Engineering, ISSN 19397038, ESCI Q2, Published online 28 March 2021, DOI: https://doi.org/10.1080/19397038.2021.1896590